IANA-FINISHER-MIB DEFINITIONS::=BEGIN-- http://www.iana.org/assignments/ianafinisher-mibIMPORTSMODULE-IDENTITY,mib-2
FROM SNMPv2-SMI -- [RFC2578]TEXTUAL-CONVENTIONFROM SNMPv2-TC;-- [RFC2579]ianafinisherMIB MODULE-IDENTITYLAST-UPDATED"200406020000Z"-- June 2, 2004ORGANIZATION"IANA"CONTACT-INFO"Internet Assigned Numbers Authority
Postal: ICANN
4676 Admiralty Way, Suite 330
Marina del Rey, CA 90292
Tel: +1 310 823 9358
E-Mail: iana@iana.org"DESCRIPTION"This MIB module defines a set of finishing-related
TEXTUAL-CONVENTIONs for use in Finisher MIB (RFC 3806)
and other MIBs which need to specify finishing
mechanism details.
Any additions or changes to the contents of this MIB
module require either publication of an RFC, or
Designated Expert Review as defined in RFC 2434,
Guidelines for Writing an IANA Considerations Section
in RFCs. The Designated Expert will be selected by
the IESG Area Director(s) of the Applications Area.
Copyright (C) The Internet Society (2004). The
initial version of this MIB module was published
in RFC 3806. For full legal notices see the RFC
itself or see:
http://www.ietf.org/copyrights/ianamib.html"REVISION"200406020000Z"-- June 2, 2004DESCRIPTION"Original version, published in coordination
with Finisher MIB (RFC 3806)."::={ mib-2 110}-- TEXTUAL-CONVENTIONs for this MIB moduleFinDeviceTypeTC::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The defined finishing device subunit process
enumerations."SYNTAXINTEGER{other(1),unknown(2),stitcher(3),folder(4),binder(5),trimmer(6),dieCutter(7),puncher(8),perforater(9),slitter(10),separationCutter(11),imprinter(12),wrapper(13),bander(14),makeEnvelope(15),stacker(16),sheetRotator(17),
inserter(18)}FinAttributeTypeTC::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"This TEXTUAL-CONVENTION defines the set of enums for use in
the finDeviceAttributeTable. See section 5.7 for the complete
specification of each attribute."SYNTAXINTEGER{other(1),deviceName(3),deviceVendorName(4),deviceModel(5),deviceVersion(6),deviceSerialNumber(7),maximumSheets(8),finProcessOffsetUnits(9),finReferenceEdge(10),finAxisOffset(11),finJogEdge(12),finHeadLocation(13),finOperationRestrictions(14),finNumberOfPositions(15),namedConfiguration(16),finMediaTypeRestriction(17),finPrinterInputTraySupported(18),finPreviousFinishingOperation(19),finNextFinishingOperation(20),stitchingType(30),stitchingDirection(31),foldingType(40),
bindingType(50),punchHoleType(80),punchHoleSizeLongDim(81),punchHoleSizeShortDim(82),punchPattern(83),slittingType(100),wrappingType(130),stackOutputType(160),stackOffset(161),stackRotation(162)}FinEdgeTC::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Specifies an edge for a Finishing Process."SYNTAXINTEGER{topEdge(3),bottomEdge(4),leftEdge(5),rightEdge(6)}FinStitchingTypeTC::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The defined stitching type enumerations. For the edgeStitch and
stapleDual enums, the finReferenceEdge attribute is recommended
to define the edge to which the operation applies."SYNTAXINTEGER{other(1),-- More information in other attributesunknown(2),stapleTopLeft(4),stapleBottomLeft(5),stapleTopRight(6),stapleBottomRight(7),
saddleStitch(8),edgeStitch(9),stapleDual(10)}FinStitchingDirTypeTC::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"Defines the direction, relative to the top sheet in the output
subunit, that the stitching operation was performed. For a
topDown(3) process, the staple will be clinched on the bottom
of the stack. This parameter can be used to determine what
order the pages of a booklet are to be printed such that the
staple clinch will be on the inside of the resulting booklet."SYNTAXINTEGER{unknown(2),topDown(3),bottomUp(4)}FinStitchingAngleTypeTC::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"This enumeration provides a description of the angular
orientation of each stitch in a single or multiple stitching
operation, relative to the 'X' axis. As with all finishing
operations, the 'X' axis is always relative to the portrait
orientation of the document regardless of the orientation
of the printed image. This enum is primarily applicable to
corner stitching operations."SYNTAXINTEGER{unknown(2),horizontal(3),vertical(4),slanted(5)}FinFoldingTypeTC::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The defined folding device process enumerations."SYNTAXINTEGER{other(1),-- More information in other attributes
unknown(2),zFold(3),halfFold(4),letterFold(5)}FinBindingTypeTC::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The defined binding type enumerations."SYNTAXINTEGER{other(1),-- More information in other attributesunknown(2),tape(4),plastic(5),velo(6),perfect(7),spiral(8),adhesive(9),comb(10),padding(11)}FinPunchHoleTypeTC::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The defined hole type punch process enumerations."SYNTAXINTEGER{other(1),-- More information in other attributesunknown(2),round(3),oblong(4),square(5),rectangular(6),
star(7)}FinPunchPatternTC::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The defined hole pattern punch process enumerations."SYNTAXINTEGER{other(1),--Pattern to be defined in other attributesunknown(2),twoHoleUSTop(4),--Letter/legal, 8.5 inch edgethreeHoleUS(5),--Letter/ledger, 11 inch edgetwoHoleDIN(6),--A4/A3, 297 mm edgefourHoleDIN(7),--A4/A3, 297 mm edgetwentyTwoHoleUS(8),--Letter/ledger, 11 inch edgenineteenHoleUS(9),--Letter/ledger, 11 inch edgetwoHoleMetric(10),--B5/B4, 257 mm edgeswedish4Hole(11),--A4/A3, 297 mm edgetwoHoleUSSide(12),--Letter/ledger, 11 inch edgefiveHoleUS(13),--Letter/ledger, 11 inch edgesevenHoleUS(14),--Letter/ledger, 11 inch edgemixed7H4S(15),--A4/A3, 297 mm edgenorweg6Hole(16),--A4/A3, 297 mm edgemetric26Hole(17),--B5/B4, 257 mm edgemetric30Hole(18)--A4/A3, 297 mm edge
}FinSlittingTypeTC::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The defined slitting type enumerations."SYNTAXINTEGER{other(1),-- More information in other attributesunknown(2),slitAndSeparate(4),slitAndMerge(5)}FinWrappingTypeTC::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The defined wrapping device process enumerations."SYNTAXINTEGER{other(1),-- More information in other attributesunknown(2),shrinkWrap(4),paperWrap(5)}FinStackOutputTypeTC::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"The defined stack output type enumerations."SYNTAXINTEGER{other(1),-- More information in other attributesunknown(2),straight(4),-- No offset, one on top of anotheroffset(5),crissCross(6)-- Rotated}END